| 當前位置：首頁->方案設計 |
|
| STPM32高精度單相電表解決方案 |
|
|
| 文章來源： 更新時間：2014/10/17 10:38:00 |
在線咨詢： |
| |
ST公司的STPM32是采用Rogowski線圈,電流變壓器或并聯電流傳感器在線測量電能的高精度集成電路,包括模擬和數字兩部分.模擬部分包括兩個可編低噪音低失調增益放大器,四個兩階24位sigmadelta ADC,兩個帶單獨溫度補償?shù)哪軒峨妷夯鶞?zhǔn),低壓降穩壓器和DC緩沖器;數字部分包括數字濾波器,硬連接的DSP,連接輸出的DFE和串行通信接口(UART/SPI).本文介紹了STPM32主要特性和框圖,DSP框圖, EVALSTPM32評估板主要特性,電路圖和材料清單.
The STPM3x is an ASSP family designed for high accuracy measurement of power and energies in power line systems using the Rogowski coil, current transformer or shunt current sensors. The STPM3x provides instantaneous voltage and current waveforms and calculates RMS values of voltage and currents, active, reactive and apparent power and energies. The STPM3x is a mixed signal IC family consisting of an analog and a digital section. The analog section consists of up to two programmable gain low-noise low-offset amplifiers and up to four 2nd order 24-bit sigmadelta ADCs, two bandgap voltage references with independent temperature compensation, a low drop voltage regulator and DC buffers. The digital section consists of digital filtering stage, a hardwired DSP, DFE to the input and a serial communication interface (UART or SPI). The STPM3x is fully configurable and allows a fast digital system calibration in a single point over the entire current dynamic range.
STPM32主要特性:
• Active power accuracy:
– <0.1% error over 5000: 1 dynamic range
– <0.5% error over 10000: 1 dynamic range
• Exceeds 50-60 Hz EN 50470-x, IEC 62053-2x, ANSI12.2x standard requirements for AC watt meters
• Reactive power accuracy:
– <0.1% error over 2000:1 dynamic range
• Dual mode apparent energy calculation
• Instantaneous and averaged power
• RMS and instantaneous voltage and current
• Under and overvoltage detection (sag and swell) and monitoring
• Overcurrent detection and monitoring
• UART and SPI serial interface with programmable CRC polynomial verification
• Programmable LED and interrupt outputs
• Four independent 24-bit 2nd order sigma-delta ADCs
• Two programmable gain chopper stabilized low-noise and low-offset amplifiers
• Bandwidth 3.6 kHz @ -3 dB
• Vcc supply range 3.3 V±10%
• Supply current Icc 4 mA (STPM32)
• Input clock frequency 16 MHz, Xtal or external
• Twin precision voltage reference: 1.23 V with independent programmable TC, 10 ppm/℃ typ.
• Internal low drop regulator @ 3 V (typ.)
• QFN packages
• Operating temperature -40 ℃~+85 ℃
圖1. STPM32框圖
圖2. STPM32 DSP框圖
EVALSTPM32評估板
The STPM3x is an ASSP family of mixed signals designed for high accuracy measurement of power and energy in power line systems using the Rogowski coil, current transformer or shunt current sensors. According to p/n, the device has up to two voltages and two current channels, for energy measurement in dual-phase and single-phase (with or without neutral current monitoring) electricity metering systems.
The STPM3x devices provide instantaneous voltage and current waveforms and calculate voltage and current RMS values, active, reactive and apparent powers and energies for each channel. Moreover, they embed a full set of calibration and compensation parameters which allow the meter to fit tight accuracy standards (EN 50470-x, IEC 62053-2x, ANSI12.2x for AC watt meters). All calculated data, as well as configuration parameters, are stored in internal 32-bit registers accessible through SPI or UART peripheral.
Three boards are available for evaluation purpose:
• EVALSTPM34 board with 2 CT
• EVALSTPM33 board with CT + shunt
• EVALSTPM32 board with shunt
EVALSTPM32評估板主要特性:
• 0.2% accuracy single-phase meter reference design
• USB port for connection to the isolated hardware programmer STEVAL-IPE023V1 and PC GUI
• RS232 and UART isolated port for connection to PC GUI
• SPI/UART switch for device peripheral selection
• 2x programmable LEDs on-board
• Digital expansion to external system-on-chip or MCU
• Power supply 3.3 V: external or through the STEVAL-IPE023V1 isolated USB board
• IEC61000 standard compliant
圖3. EVALSTPM32評估板外形圖
圖4. EVALSTPM32評估板電路圖
圖5. EVALSTPM3x評估板電路圖(RS232/UART)
圖6. EVALSTPM32評估板單相系統連接圖 |
| |
|
|
|
|
|
| |
|
| |
|
|
